Schedule maintenance for air conditioning units before summer, ideally in October or November. If you use a reverse-cycle system for heating, book a professional service in April or May, before the colder months. A system that heats your home needs attention before winter, not just before summer.
It’s easy to focus on cooling when the weather warms up, but a neglected unit can also struggle when you switch it to heating. Dirty filters can restrict airflow and affect a unit’s energy use.
This guide covers when to book a service, how often to clean or replace filters, and what maintenance may include. You’ll also learn which signs to watch for, how upkeep can affect energy use, and why reverse-cycle systems need seasonal care for both heating and cooling. Use these practical steps to prepare your unit and keep it working as it should.
Key Takeaways
- Clean filters regularly, and switch the unit off before removing one. Check the manual for replacement guidance.
- Plan a cooling service before summer, ideally in October or November. For reverse-cycle heating, April and May are useful times to prepare.
- Service needs vary by system and use. Commercial units may need more frequent attention than residential systems.
- Cooling and heating systems account for approximately 40 per cent of an average household’s total energy use in Australia, according to Australian Government, YourHome.
- If your split system is your primary heater, clean its filters between June and August to help maintain airflow through winter.
Table of Contents
1. Do I clean or replace my filters?
Clean reusable filters when dust builds up, and replace disposable filters when they’re dirty or damaged. With regular use, clean air conditioner filters every two to four weeks. The right interval depends on how often you run the unit and how quickly dust collects. Homes with pets, renovations or open windows may need more frequent checks than less dusty spaces.
Switch the air conditioning unit off before removing its filters. Follow the manual, then slide each filter out carefully. For a reusable filter, remove loose dust and wash it as directed. Let it dry fully before reinstalling it. A wet filter can restrict airflow and encourage moisture inside the unit. Replace disposable filters with the type and size specified in the manual.
CHOICE recommends cleaning air conditioner dust filters at least twice a year. That’s a useful minimum, but regular use may call for cleaning every two to four weeks. Check filters in fall and spring, then inspect them more often during periods of heavy cooling or heating. Dust on indoor-unit louvres or ceiling vents is another reason to check the filter and airflow.
A dirty filter restricts the air passing through the unit. The system may then work harder to move air across the evaporator, affecting performance and energy use. Cleaning or replacing dirty filters can help the system operate efficiently. Filters also catch airborne dust before it circulates through the room, but they can’t remove every indoor pollutant. Keep the unit’s filter clean, and follow its manual when choosing a replacement.
Electrical checks are separate from filter care. Cleaning a filter doesn’t confirm that wiring or electrical components are safe, and inspection timing depends on the unit’s condition and installation. If you notice a damaged cord, scorching, unusual electrical smells or repeated power interruptions, stop using the unit and arrange an assessment. Don’t remove covers or touch wiring.
Cleaning a filter is a simple upkeep task, but internal repairs are different. Attempting repairs can damage electrical parts or the refrigerant circuit, and refrigerant handling requires specialist knowledge. Don’t open refrigerant lines or try to top up refrigerant yourself. If the unit still performs poorly after you clean its filters, note the symptoms, such as weak airflow, and arrange professional maintenance.
Replace a filter rather than cleaning it if the manual identifies it as disposable, or if it’s torn, misshapen or won’t sit securely. A clean, correctly fitted filter supports airflow and helps limit dust entering the system. Keep the manual handy for the filter type, cleaning method and replacement instructions.
2. When should I service my air conditioner?
In Australia, arrange professional air-conditioner servicing before summer, ideally in October or November. If you use a reverse-cycle system for heating, April or May are good months to service it ahead of cold weather. Consider professional servicing once your unit has been installed for a year or more.
For a home system, plan an annual check as a practical starting point, then bring it forward if you notice a problem. Coils should be checked at least once per year. If the outdoor unit sits in a dusty area, garden or spot exposed to mower debris, check its coils every 6 months. Dust and plant matter can build up around the outdoor coil and affect airflow.
Commercial servicing frequency depends on the system type and workload. Small-office commercial split systems are recommended for service twice a year. Commercial ducted systems should be serviced at least twice a year, with quarterly servicing for high-demand use. High-demand or critical commercial HVAC systems need monthly operational inspections. These intervals match checks to the system’s operating demands.
Check the indoor and outdoor sections between services. Dust on indoor-unit louvres or ceiling vents can signal that the system needs attention. Notice whether airflow feels weaker than usual or the unit struggles to operate normally. Outside, look for garden growth, leaves and mower debris near the condenser. Keep the surrounding area clear for airflow, and note visible damage without opening the unit.
A system can show signs of trouble before its planned service date, so note when a change starts and which mode was running, such as cooling or heating. Record whether the issue affects one room or several. This information helps you describe the symptoms clearly when arranging maintenance for air conditioning units.
Regular maintenance should include coil checks, and a service visit can also assess the system’s general operation. The work required depends on the unit and its condition. A split system used occasionally in a clean room may need a different schedule from a commercial ducted system under high demand. Keep a simple record of service dates, observed changes and completed work.
If your unit is due for a professional service, air-conditioning maintenance can help keep its condition and operating needs in view. Book ahead of the seasonal change, especially if you rely on the same conditioning system for summer cooling and winter heating.
3. Maintenance plans for residential and commercial systems
A maintenance plan schedules recurring inspections around the air conditioning system’s type and workload. For a home split system, that can mean planned cleaning and checks before cooling or heating demand rises. A commercial plan needs to account for operating hours, occupied areas and the impact of interrupted service. Read the task list carefully: scheduled maintenance and repairs are separate work.
A typical annual tune-up includes inspecting and cleaning coils, replacing filters, checking fans and blowers, and inspecting refrigerant levels and pressure. Other common tasks include flushing drains, cleaning the fascia and grilles, checking wiring connections, and assessing refrigeration operation. The work varies with the system’s condition. Ask for a record of completed tasks and any issues identified.
System type shapes the maintenance checklist. A split system has an indoor head and an outdoor unit, while a multi-head system connects several indoor units to shared outdoor equipment. Ducted systems also have ducts, ceiling vents and return-air grilles. Rooftop systems place equipment on the building roof, making safe access and checks of exposed components important.
- Split and multi-head systems: inspect indoor filters, coils, fans, drains and controls, then assess the outdoor coil and connections.
- Ducted systems: check filters, return-air grilles, vents, drains and accessible ductwork for airflow issues or visible damage.
- Rooftop systems: include coil cleaning, fan checks, wiring connections and refrigeration operation in the service scope.
- Fresh air ventilation: inspect the system’s airflow path and components, especially where ventilation supports occupied or critical spaces.
For commercial buildings, match the plan to the equipment and operating demand. Small-office commercial split systems are recommended for service twice a year. Commercial ducted air conditioning systems need servicing at least twice a year, with quarterly servicing for high-demand use. Commercial fresh air ventilation systems also need servicing at least twice a year, or quarterly in critical environments. High-demand or critical HVAC systems need monthly operational inspections.
These intervals help facilities managers plan access and limit disruption. For example, arrange a visit when rooms are less occupied, and group checks across several units where practical. Keep a system register with equipment type, service dates, observed issues and completed work. That record makes it easier to spot whether recurring dirty filters or blocked drains affect one unit or several.
Residential plans can focus on scheduled upkeep for the equipment serving the home. Commercial plans may coordinate visits across split, ducted, rooftop and ventilation equipment. For homeowners exploring residential setups or installation standards, providers such as essexhomeairconditioning.co.uk offer helpful insights into how domestic systems are professionally installed and maintained. In either setting, confirm which inspections and cleaning tasks are included, and treat repairs separately. A clear scope makes each service visit easier to understand and track.

Air conditioner efficiency and energy bills
In Australia, cooling and heating systems account for approximately 40 per cent of an average household’s total energy use, according to Australian Government, YourHome. That makes an air conditioning unit’s condition relevant to household energy use, but it isn’t the only influence on a bill. The unit’s size, how often it runs, the weather and the home’s insulation all affect electricity consumption.
Start with the outdoor unit. Keep leaves, grass clippings and vegetation clear of its airflow path. Garden debris can obstruct airflow and make the system work harder. Check the area after mowing or trimming, and look for visible damage around the casing or coil. Don’t bend coil fins or remove covers while clearing debris.
Ducts matter too. In homes with ducted cooling, air can lose effectiveness as it travels through ducts in hot attics or crawl spaces. Insulating ducts in these areas can improve air conditioning effectiveness. If one room feels much warmer than another, note which vents are affected and whether airflow changes while the system runs. This information can help pinpoint where to investigate.
- Use the system deliberately: choose a comfortable temperature, close doors and windows while it runs, and switch it off when cooling or heating isn’t needed.
- Reduce heat entering the home: use curtains or blinds on sunny windows, especially in rooms that become hot during the afternoon.
- Watch for changes: record unusual running patterns, uneven temperatures or a bill increase across comparable billing periods.
These steps address different sources of energy demand. Shading a west-facing room, for example, can reduce heat entering that space, while clearing debris protects airflow around the outdoor unit. A ducted system may also need attention to duct insulation, whereas a split system doesn’t distribute conditioned air through the same duct network.
A sudden bill increase doesn’t prove that the air conditioning unit is at fault. Compare similar billing periods and consider changes in weather, household occupancy and how often cooling or heating ran. Then note system changes, such as longer operating periods, weak airflow or uneven room temperatures. This gives a clearer picture than relying on one bill alone.
Efficiency depends on the whole setup, not just the unit. A clean, unobstructed outdoor area, suitable duct insulation and sensible operation each address a different cause of wasted energy. If you notice damage, persistent airflow changes or unusual operating patterns, arrange a professional assessment rather than opening the equipment. Record what changed and when so the assessment can focus on the symptoms.
5. Reverse-cycle heating maintenance
A reverse-cycle air conditioner provides cooling and heating, so prepare it for both seasons. Book a professional service for heating in April or May, before the cold months. The recommended service window before summer is October or November. Seasonal maintenance helps address heating operation before winter demand begins, rather than discovering an issue during a cold spell.
Heating mode uses the same main components as cooling, including the compressor and refrigerant circuit. The system transfers heat rather than producing warmth through a separate heating element. A technician can assess heating-mode operation, inspect coils and fans, and check that the unit responds to its controls. If heating feels weak or uneven, note which rooms are affected and when the change occurs.
Filters need attention during winter too. If a split system is your home’s primary heater, clean its filters between June and August. Dust restricts airflow, which can affect how the unit distributes warm air. Follow the manual’s cleaning instructions, and refit each filter only when it’s dry. A clean filter supports airflow, but it doesn’t replace a professional check of the compressor, coils or refrigerant operation.
Before switching to heating, check the indoor unit and the area around the outdoor unit. Clear leaves and garden debris that could obstruct airflow. Look for dust on louvres, blocked vents or visible damage, and keep furniture clear of indoor outlets. Don’t open electrical panels or refrigerant lines. If the system makes an unusual noise or doesn’t deliver warm air, record the mode and symptoms for a technician.
Weather can affect how hard a reverse-cycle system works. A home that loses heat quickly may feel less comfortable, even when the unit runs longer. Close doors to unused rooms where appropriate, draw curtains after sunset and keep indoor vents unobstructed. These steps help heated air reach the spaces you use, without changing the system’s settings or opening its casing.
Regular servicing also matters for the system’s working life. Without regular servicing, an air conditioner may last fewer than 10 years and may need replacement at a cost of thousands of dollars. That isn’t a reason to replace a unit simply because it’s ageing. Use its service history, performance in heating mode and visible condition to guide the decision.
Keep a simple seasonal record: note service dates, filter cleaning and changes in heating performance. If your reverse-cycle unit needs professional attention before winter, arrange air conditioning maintenance so its heating operation can be assessed before colder weather arrives.
Aircool: Air Conditioning Upgrade under government rebate
If your current system no longer suits your home’s heating and cooling needs, Aircool’s Air Conditioning Upgrade under government rebate can be a practical next step. Consider whether a replacement setup would better match the rooms you use and the way you live, rather than continuing with a unit that struggles to serve the space.
Aircool supplies and installs Split System, Multi-Head Split and Ducted options. A split system can suit one area, while a multi-head setup serves several rooms. Ducted air conditioning provides a whole-home approach. The right option depends on your layout, comfort needs and how you want to control different spaces.
For help considering an air conditioning upgrade, contact Aircool through its website.
Plan your next step with confidence
Use your next service decision to think beyond the immediate season. Note which rooms need cooling or heating, how the household uses them, and whether the current layout still works. This gives you a practical brief for planning maintenance for air conditioning units or considering a different system as your needs change.
If ongoing upkeep no longer suits your home, Aircool offers an Air Conditioning Upgrade under government rebate, as well as Multi-Head Split and Ducted systems. These options suit different layouts, from several rooms needing separate indoor units to a whole-home setup. A clear outline of your comfort priorities helps make the next conversation more useful.
Bring your questions and system requirements to Aircool. Contact Aircool for maintenance advice and take a straightforward next step towards a setup that suits your home.
Frequently Asked Questions
When should I service my air conditioner?
Arrange servicing before the season when you’ll rely on the system most. In Melbourne, book cooling maintenance before summer, ideally in October or November. If your reverse-cycle unit heats your home, April or May is a sensible time to prepare for colder weather. Bring servicing forward if you notice a new noise, uneven temperatures or reduced airflow, and describe when the change started.
Do I clean or replace my filters?
Clean reusable filters and replace disposable ones. Check the unit’s manual to identify the filter type and how to handle it. With the system switched off, remove a dusty reusable filter, clean it as directed and let it dry fully before refitting. Replace a filter that’s torn or won’t sit securely. A poor fit can let dust pass into the system.
How can my drain become blocked?
An air conditioner’s drain can clog when dust, biological growth or other debris collects in the drain pan or pipe. A blockage may cause water to leak from the indoor unit instead of flowing outside. If you spot water near the unit, switch it off and protect nearby flooring. Don’t push wire or tools into the pipe, as this can damage the drain or push the blockage further inside.
How do I clean my air conditioner?
Switch the unit off before cleaning accessible surfaces. Wipe the indoor fascia and louvres with a soft, slightly damp cloth, following the manufacturer’s instructions. Clean reusable filters separately and let them dry before reinstalling. From ground level, remove loose leaves near the outdoor unit without opening its casing. Avoid spraying water into electrical sections or using harsh chemicals, which may damage surfaces or components.
How do I fix a dirty or damaged coil?
Leave a damaged coil or heavy internal dirt to a qualified air-conditioning technician. Coil fins bend easily, and aggressive brushing or pressure washing can make the damage worse. If the outdoor coil is dusty, switch the system off and clear loose leaves around the unit without touching the fins. Note visible damage or reduced performance, then arrange an assessment for cleaning or further work.
How do I take care of my air conditioner?
Build a simple routine around the unit’s manual and seasonal use. Keep a note of filter cleaning, unusual sounds, leaks and changes in airflow. Keep furniture clear of indoor outlets, and remove leaves around the outdoor unit. Before Melbourne’s summer or winter demand, check that the controls respond and air reaches the rooms you use. Leave internal electrical and refrigerant components to a professional.
How much does AC maintenance cost?
The price of a maintenance plan depends on the system type, condition, access and work included. A plan covering several units or ducted equipment has a different scope from scheduled upkeep for one split system. The price is provided after a quote request, based on those requirements. Review the listed inspection and cleaning tasks to compare the plan’s scope with your property’s needs.
How much does a service cost?
A one-off service price depends on the air conditioner type, access to its components, condition and required tasks. A standard inspection differs from extra cleaning or investigating an operating issue. The price is provided after a quote request, based on the system and service scope. For a Melbourne home, note the unit type and any symptoms before requesting a quote, so the work needed is clear.




